Effect of microstructural features on the corrosion behavior of severely deformed Al–Mg–Si alloy

The aim of this study was to determine the influence of severe plastic deformation processing and the changes in microstructure resulting therefrom on the corrosion resistance of an Al–Mg–Si alloy. The alloy was processed using incremental equal channel angular pressing, which caused a reduction in grain size from 15 to 0.9 µm. The grain refinement was accompanied by an increase in the number of grain boundaries and dislocations, and by changes in grain orientation. However, there was no change in the size and number of intermetallic particles, which presumably resulted in a constant number of galvanic couplings. Electrochemical experiments revealed only slight differences between the samples before and after processing. Higher potential transients/oscillations upon immersion and increased corrosion currents in the vicinity of corrosion potential point to slightly higher reactivity of the most refined material. This indicates that intermetallic particles are the most crucial microstructural elements in terms of corrosion resistance. Their impact exceeds that of grain boundaries, in particular, at the stage of corrosion initiation. The development of corrosion attack is controlled more by the microstructure of the matrix as the grain refinement resulted in a less pronounced corrosion attack in comparison with the coarse-grained sample.     

Surface modification of superfine SiC powders by ternary modifiers-KH560/sodium humate/SDS and its mechanism

SiC is a promising functional ceramic material with many great properties. High concentrated SiC slurry with excellent rheology and stability is required in some processes of ceramic forming. In this work, the dispersion of SiC powders was obviously improved by ternary modifiers: γ-(2,3-epoxypropoxy) propytrimethoxysilane (KH560), sodium humate and sodium dodecyl sulfate (SDS). Modified SiC slurry showed the lowest viscosity of 0.168 Pa s at a solid content of 50 vol%. The maximum absolute value of zeta potential of SiC increased from 47.3 to 61.6 mV by modification. Sedimentation experiments showed that a highly stable suspension of modified SiC was obtained at pH 10. SiC green body with high density of 2.643 g/cm³ was prepared with modified powders by slip casting. X-ray photoelectron spectra (XPS) and thermogravimetry (TG) measurements indicated the adsorption of modifiers on SiC surface. Therefore, modified SiC powders could stably disperse in aqueous media due to the increase of electrosteric repulsion between particles. The novel strategy used in this study could further improve the dispersion of SiC powders.     

Manufacturing catalyst-coated membranes by ultrasonic spray deposition for PEMFC: Identification of key parameters and their impact on PEMFC performance

This study deals with the manufacturing of catalyst-coated membranes (CCMs) for newcomers in the field of coating. Although there are many studies on electrode ink composition for improving the performance of proton-exchange membrane fuel cells (PEMFCs), there are few papers dealing with electrode coating itself. Usually, it is a know-how that often remains secret and constitutes the added value of scientific teams or the business of industrialists. In this paper, we identify and clarify the role of key parameters to improve coating quality and also to correlate coating quality with fuel cell performance via polarization curves and electrochemical active surface area measurements. We found that the coating configurations can affect the performance of lab-made CCMs in PEMFCs. After the repeatability of the performance obtained by our coating method has been proved, we show that: (i) edge effects, due to mask shadowing - cannot be neglected when the active surface area is low, (ii) a heterogeneous thickness electrode produces performance lower than a homogeneous thickness electrode, and (iii) the origin and storage of platinum on carbon powders are a very important source of variability in the obtained results.     

Thermal properties of hierarchical YSZ and LZO ceramic microspheres with multi-scaled voids investigated by using theoretical,experimental and simulation methods

Heat transfer within ceramic feedstock powders is still unclear, which impedes optimization of the thermal and mechanical properties of the thermal sprayed coatings. The microspheres (yttria-stabilized zirconia YSZ and lanthanum zirconate LZO) were prepared via the electro-spraying assisted phase inversion method (ESP). The thermal properties of the two ESP microspheres and a commercial hollow spherical powder (HOSP) were investigated by using theoretical, experimental, and simulation methods. Thermal conductivity of the single microsphere was estimated via a novel nest model that was derived from the Maxwell-Eucken 1 and the EMT model. Thermal conductivity of a single YSZ/LZO-ESP microsphere prepared at 1100–1200 °C was within 0.36–0.75 W/m K, which was ～ 20 % lower than that of a single YSZ-HOSP microsphere with a similar porosity. Heat flux simulation showed that high tortuosity around the multi-scaled voids of the ESP microsphere led to a more efficient decrease in thermal conductivity compared with total porosity.     

纳米碳化钒/碳化铬复合粉末的微波辅助高能球磨合成及其应用

以微米级氧化钒(V2O5)、氧化铬(Cr2O3)和纳米碳黑为原料，采用机械合金化及微波辅助加热法制备了纳米碳化钒/碳化铬复合粉末。利用XRD、XPS、TG-DSC、SEM、TEM和BET对产物进行了分析表征。结果表明，：纳米碳化钒/碳化铬复合粉末的最佳合成条件为：碳的质量分数为35%，反应温度为900℃，保温时间为1h。在该条件下的反应产物主要由V3Cr2C5、Cr2VC2和Cr3C2组成，颗粒为球形或类球形，分散性较好，无明显团聚现象，平均颗粒尺寸约为50nm，复合粉末的比表面积为115.53m2/g。添加纳米碳化钒/碳化铬复合粉末可以提高陶瓷结合剂cBN磨具的力学性能和磨削效率，降低磨具的损耗，并且对磨具具有减摩作用。     

Research on the effects of surface modification of ceramic powder on cure performance during digital light processing (DLP)

Digital light processing (DLP) is one of the most important additive manufacture technologies to fabricate ceramic parts with complex geometries. Compared with pure photosensitive resin, the cure performance of ceramic suspensions is obviously different due to the optical property change after the addition of ceramic powders. In this paper, a unique oxidation process was used to modify the optical properties of nitride powders including AlN and Si₃N₄. The properties of oxidized ceramics were investigated and the cure performance of ceramic suspensions was then characterized. The effect of oxidation time on cure performance was evaluated. The results showed that for AlN, oxidation process leads to the smaller cure depth and smaller excess cure width as compared with non-oxidized AlN and for Si₃N₄, oxidation process leads to the larger cure depth and larger excess cure width as compared with non-oxidized Si₃N₄, indicating that both refractive index and light absorbance of ceramic powders have obvious effects on cure behaviors. Additionally, the cure behavior of oxidized ceramic suspension in this study shows that the relationship of cure depth vs. incident energy agrees well with Beer- Lambert model, but the excess cure width vs. incident energy is not consistent with quasi Beer-Lambert model due to the nature of digital micromirror device (DMD).     

Sintering behavior of Ni–Zn ferrite powders prepared by molten-salt synthesis

Ni_0.5Zn_0.5Fe₂O₄ powders were prepared by a novel molten-salt synthesis method. The effects of calcination processes of the powders on their sintering behaviors were investigated. Compared with the synthesis by traditional solid-state reaction, the proposed molten-salt method can significantly reduce the synthesis temperature of Ni_0.5Zn_0.5Fe₂O₄ from 800 to 550°C below, and the prepared powders have relatively high sintering activity at low temperature, which can thus decrease the sintering temperature. However, the abnormal growth of grains is easy to occur during sintering, thus resulting in uneven grain size. In particular, during the molten-salt synthesis, the holding time for calcination is a dominant factor affecting the activity and crystallization degree of the resultant powders. From the point of view of increasing the density of sintered bodies, the optimal conditions for synthesizing Ni_0.5Zn_0.5Fe₂O₄ powder by the proposed molten-salt synthesis is 400°C for 6 h. In addition, the saturate magnetization of the finally obtained ferrite ceramics has nothing to do with the preparation processes, while their coercivity depends on their densification and grain size caused by their different processing routes.     

超声波辅助插层-剥离法制备煤系高岭土微粉的研究

我国煤系高岭土储量丰富,为满足造纸、纺织等行业个性化的需求,通常要对其进行深加工。以山西朔州煤系高岭土为原料,分别在恒温磁力搅拌和超声波作用下探究了煤系高岭土/二甲基亚砜(DMSO)插层复合物制备的最佳条件,在插层复合物的基础上对煤系高岭土进行超声辅助剥离,制备得到高岭土微粉,并利用XRD、SEM、BET、TG-DSC等方法分析表征样品。正交实验结果表明在磁力搅拌条件下DMSO用量、插层时间以及插层温度均对插层率具有一定的影响,引入超声波有利于高岭土插层率的提升。插层复合物经超声辅助剥离后晶粒厚度明显减小,高岭土片层状结构大体上呈现碎片化,仅保留少部分大的片状结构,其边缘碎化,整体上也出现碎裂的趋势。剥离样品的比表面积和孔径均大幅度增加,为硬质高岭土的剥离和超微细粉体的制备提供了新的思路。